• NewFC is now officially an archive. Please go to FuckCombustion for more information. If you have an account there, use it. If you changed your account name when you registered here, use your FC account. If you did not have an FC account, please register one. Thanks to everyone for their patience.

Magic Flight Launch Box

TommyDee

Well-known Member
Messages
386
The 3800mah Sub-C cell was enough for a trench for me. I went to 4200mah to be sure :cheers:
 
TommyDee,
  • Like
Reactions: Vapirtoo

Vapirtoo

Member
Messages
23
The EBL 2800 are still impressing me on the run. You have to use the
old style of sip and pull slowly, but the taste and effects are awesome.
Went back to the PA for some desktop action, and I really had to back the heat off!
The batts force you to have a meditative, slow relaxed session... no coughing!
I use different vapes according to my mood. ( I'm high and mood looks like a foreign word).
 

Junny89

Member
Messages
34
Can anyone advise what grinder they are using
And
Also what consistency they are grinding to?
I found a small tiny tiny silver grinder MF sent me with my order in the box but it’s grind is no where near as fine as the finishing grinder. Not getting that hit I always get with the fine grind.
just find it tedious grinding with one and then again in the finishing grinder. Wanted just one grinder I can use in emergency with that fine grind.
 
Junny89,

TommyDee

Well-known Member
Messages
386
I do a two-step grind @Junny89 . I run 2 grams through a generic grinder (favorite $5 unit 3 years old and in perfect shape after #'s of bud.). I then get one of those wire kitchen strainers. It sits in a silver condiment tray having a similar shape, and fitting the screen nicely [read-no spill-over]. I then proceed to rub the herb with my finger until only water-leaf stems remain. Now I have an herb that is kief and dense flower. A bit of sticky on one finger and 3-4 days supply. I keep these in airtight pop-top containers.

One tip - keep those water-leaf stems. They never combust in a launch box. You can toast the hell out of the stems and it will you a really nice buzz.

This is what my ABV comes out like. Kief gone and this is a good sample of what the leaf comes out like. It does take a bit more brushing, but of so tasty!

20200315_180038.jpg
 
TommyDee,
  • Like
Reactions: Vapirtoo

Junny89

Member
Messages
34
I do a two-step grind @Junny89 . I run 2 grams through a generic grinder (favorite $5 unit 3 years old and in perfect shape after #'s of bud.). I then get one of those wire kitchen strainers. It sits in a silver condiment tray having a similar shape, and fitting the screen nicely [read-no spill-over]. I then proceed to rub the herb with my finger until only water-leaf stems remain. Now I have an herb that is kief and dense flower. A bit of sticky on one finger and 3-4 days supply. I keep these in airtight pop-top containers.

One tip - keep those water-leaf stems. They never combust in a launch box. You can toast the hell out of the stems and it will you a really nice buzz.

This is what my ABV comes out like. Kief gone and this is a good sample of what the leaf comes out like. It does take a bit more brushing, but of so tasty!

View attachment 1595
ahh ok so I do something similar. I use a normal grinder first and then use the-magic flight finishing grinder And it similar albeit not as fine as yours. However this method works wonders. I do this every few days and fill both sides of the optional stash box. I’ve recently just started doing this and find its awesome.

I just wanted a grinder that would remove the 2 stage process and just do it in one go- in emergency. sometimes I just don’t get the time to grind twice.

that finishing grinder looks tiny, like it won’t work but it really does the trick and surprised me.
(it’s not as effective on bud pieces, it has to be ground already to become even finer)
 
Junny89,
  • Like
Reactions: Vapirtoo

TommyDee

Well-known Member
Messages
386
Yea me too. Haven't seen one that can do what the screen does. Getting a grind as fine as I like will take a very good grinder with a very fine grind plate. I'm very happy with my process and the results. It can certainly be improved. But it works in the LB and the VC. I've seen some kind of mill that uses a screen and runs a series of close running blades over the dome. A lot of things just gum up when it gets too fine, don't you think?
 
TommyDee,
  • Like
Reactions: Vapirtoo

Junny89

Member
Messages
34
Yea me too. Haven't seen one that can do what the screen does. Getting a grind as fine as I like will take a very good grinder with a very fine grind plate. I'm very happy with my process and the results. It can certainly be improved. But it works in the LB and the VC. I've seen some kind of mill that uses a screen and runs a series of close running blades over the dome. A lot of things just gum up when it gets too fine, don't you think?
Yes I know which you mean. It’s the flower Mill USA grinder and is like over $120 plus shipping and customs etc. You swap the discs for different grinds etc.
Yes your right they do and surprised your vapcap hasn’t yet. The LB is ok as it’s in a trench.
 
Junny89,

TommyDee

Well-known Member
Messages
386
I cheat with the VC. I know how to make it breath this stuff. I draw the load with a dip&twist in the stash and I use the inverted CCD. And the cap has been relieved. I can vacate a cap in one draw to dark ABV... that hurts though. Can't do that with the LB. LB is for a session. VC is for medicating.
 
TommyDee,

archangelz001

FIRE!!!
Messages
6
Location
Left Coast, SF Bay Area
0.1gm goes into the MF Nano grinder, give it a few twists,, then dumped into the MF Finishing grinder sitting on LB. Yeah it's a 2-step, but hey, it comes out perfectly fluffy and just fills the trench. It's just part of the ritual so enjoy. :brow::ko:
 
archangelz001,
  • Like
Reactions: TommyDee

Junny89

Member
Messages
34
@TommyDee i use that method of dip and twist also works a treat and stops over filling.

@archangelz001 how do you use that nano grinder! It keeps slipping from my hands it’s so annoying ! It’s cute don’t get me wrong but a pain to use lol
I do them steps also, I was just curious to know if any other grinder just provided 1 step for everything. My secret stash is full of some herb but I got some testers yday of some other top shelf herb and really wanted to try it in the MFLB. Sadly I just didn’t get the time for the 2 step process. I ended up using the nano grinder and dumping in the MFLB. To no surprise it didn’t go down well as the herb wasn’t as fine and struggled to smoke it tbh.
If you don’t prep the MFLB in advance (in emergency situations) it does go unused for me as I don’t always get time to prep etc.

I’m actually surprised at the ingenuity of the finishing grinder. It’s more of a shredder than anything. I’ve only just seen more shredder style grinders only coming out now, to think MF did this so long ago! Hats of to them for starting this new trend.
If anyone was interested this is the link to that flower Mill shredder and yes it’s $125!

 
Last edited:
Junny89,

archangelz001

FIRE!!!
Messages
6
Location
Left Coast, SF Bay Area
@TommyDee i use that method of dip and twist also works a treat and stops over filling.

@archangelz001 how do you use that nano grinder! It keeps slipping from my hands it’s so annoying ! It’s cute don’t get me wrong but a pain to use lol
I do them steps also, I was just curious to know if any other grinder just provided 1 step for everything. My secret stash is full of some herb but I got some testers yday of some other top shelf herb and really wanted to try it in the MFLB. Sadly I just didn’t get the time for the 2 step process. I ended up using the nano grinder and dumping in the MFLB. To no surprise it didn’t go down well as the herb wasn’t as fine and struggled to smoke it tbh.
If you don’t prep the MFLB in advance (in emergency situations) it does go unused for me as I don’t always get time to prep etc.

I’m actually surprised at the ingenuity of the finishing grinder. It’s more of a shredder than anything. I’ve only just seen more shredder style grinders only coming out now, to think MF did this so long ago! Hats of to them for starting this new trend.
If anyone was interested this is the link to that flower Mill shredder and yes it’s $125!

@Junny89, my process is pretty simple. I place the Finishing grinder on the LB where it fits perfectly. I hold it down with one hand and grind/shred with the other. Occasionally it slips but I don't consider it an issue. Weighing the herb to 0.1gm, Nano grinding, dumping into the Finishing grinder and grinding takes all of several minutes. What's your hurry? :brow::lol:

Modnote: Fixed quote tags
 
Last edited by a moderator:
archangelz001,
Top Bottom